Adaptec 1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps Specifications download pdf (Page 149)

Partitioning Changes from ESX 4.x to ESXi 5.x

The ESXi partition scheme used in ESXi 5.x differs from that of earlier ESX and ESXi versions. ESXi 5.x does

not have the Service Console partition found in ESX.

How these changes affect your host depends on whether you are upgrading to ESXi 5.x or performing a

fresh installation.

Partitioning in New ESXi 5.x Installations

In new installations, several new partitions are created for the boot banks, the scratch partition, and the

locker. New ESXi 5.x installations use GUID Partition Tables (GPT) instead of MSDOS-based partitioning.

The partition table is fixed as part of the binary image, and is written to the disk at the time the system is

installed. The ESXi installer leaves the scratch and VMFS partitions blank, and ESXi creates them when the

host is rebooted for the first time after installation or upgrade. The scratch partition is 4GB. The rest of the

disk is formatted as a VMFS5 partition.

NOTE The installer can create multiple VFAT partitions. The VFAT designation does not always indicate

that the partition is a scratch partition. In some cases, a VFAT partition can lie idle.

Partitioning in Upgraded ESXi 5.x Hosts

Upgraded systems do not use GUID Partition Tables (GPT), but retain the older MSDOS-based partition

label.

For most ESXi 4.x hosts, the partition table is not rewritten in the upgrade to ESXi 5.x. The partition table is

rewritten for systems that have lopsided bootbanks. Lopsided boot banks can occur in systems that are

upgraded from ESXi 3.5 to ESXi 4.x, and then upgraded directly to ESXi 5.x.

For ESX hosts, the partitioning structure is changed to resemble that of an ESXi 4.x host. The VMFS3

partition is retained and a new MSDOS-based partition table overwrites the existing partition table.

For ESX hosts, any data stored in custom user created partitions inside the Service Console is not preserved

in the migration to ESXi 5.x.

Upgraded hosts do not have a scratch partition. Instead, the scratch directory is created and accessed off of

the VMFS volume. Each of the other partitions, such as the bootbanks, locker and vmkcore are identical to

that of any other system.

In upgraded hosts, the VMFS partition is not upgraded from VMFS3 to VMFS5. ESXi 5.x is compatible with

VMFS3 partitions. You can upgrade the partition to VMFS5 after the host is upgraded to ESXi 5.x. See the

information on upgrading datastores to VMFS5 in the vSphere Storage documentation.

Upgraded hosts, which keep the older MSDOS-based partitioning, do not support installing ESXi on a single

physical disk or LUN larger than 2TB. To install ESXi on a disk or LUN larger than 2TB, you must do a fresh

installation.

NOTE The ESXi 5.x installer cannot detect ESX 2.x instances or VMFS2 datastores. You cannot migrate ESX

2.x instances to ESXi 5.x or preserve VMFS2 datastores in an upgrade to ESXi 5.x. Instead, perform a fresh

installation of ESXi 5.x.

For the VMFS partition on the disk to be preserved during an upgrade to ESXi 5.x, the partition must be

physically located after the boot partition, which is partition 4, and the extended partition on the disk (8192

+ 1835008 sectors). Any system that has a VMFS partition after the 1843200 sector mark can keep that VMFS

partition, regardless of whether it was initially installed with ESX 3.5 or 4.x.

For systems in which the VMFS partition is placed on a different drive from the boot drive, the entire

contents of the boot drive is overwritten during the upgrade. Any extra data on the disk is erased.

Chapter 7 Upgrading and Migrating Your Hosts

VMware, Inc. 149

1 2 ... 144 145 146 147 148 149 150 151 152 153 154 ... 225 226

Adaptec 1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps Specifications Page 149

Comments to this Manuals

Adaptec 1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps Specifications Page 149

Comments to this Manuals

Related products and manuals for System management software Adaptec 1130U2 - Storage Controller RAID)- U2W SCSI 80 MBps