Adaptec ASC39320A-ROHS-KIT User's Guide

USER’S GUIDEADAPTEC ULTRA320 SCSI CARDS(39320A, 29320A, 29320ALP)U320 UG.book Page 0 Tuesday, September 23, 2003 1:47 PM

xAdaptec Ultra320 SCSI Cards User’s Guide3 Configuring the Adaptec SCSI Card with SCSISelect Starting SCSISelect 3-3Exiting SCSISelect 3-4Using SCSISe

9-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Installing Windows NTThe adpu320.sys driver is not embedded on the Windows NT 4.

9-3Installing the SCSI Driver for Windows NT 4.08 To add other host adapters that are not part of the Ultra320 Family, press S and repeat from Step 5

9-4Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Windows NT 4.0 Already Installed To update or install the adpu320.sys driver if

9-5Installing the SCSI Driver for Windows NT 4.0Using Advanced Configuration ParametersAdvanced users may use software parameters to alter the configu

9-6Adaptec Ultra320 SCSI Cards User’s GuideNote: The file hotp320.reg adds Hot-Plug related entries into the NT Registry, including the driver-specifi

9-7Installing the SCSI Driver for Windows NT 4.0To eliminate the Warning message, you must update the Windows NT 4.0 software configuration, described

9-8Adaptec Ultra320 SCSI Cards User’s GuideTo swap adapters:1 Install the driver for the Ultra320 Family host adapter by following the steps in Instal

9-9Installing the SCSI Driver for Windows NT 4.0TroubleshootingProblems and SolutionsI made changes to the host adapter configuration and Windows NT 4

9-10Adaptec Ultra320 SCSI Cards User’s Guide If the error message persistsa Restart your computer system to a DOS prompt again and copy the current v

9-11Installing the SCSI Driver for Windows NT 4.06 At the DOS prompt do a change directory to I386. 7 Once you are in the I386 directory, type WinNT /

xiContents5 Installing the HostRAID Driver for Windows 2000, 2003, and XP Installing the Device Driver for Windows 5-2Installing the Driver For a Fre

10-1100Installing the SCSI Driver for Novell NetWare In this Chapter...This chapter explains how to install the Adaptec Ultra320 SCSI driver adpu320.h

10-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Installing NetWareTo install the adpu320.ham driver when you install NetWare, f

10-3Installing the SCSI Driver for Novell NetWareInstalling the Driver When NetWare is Already InstalledTo update or install the adpu320.ham driver wh

10-4Adaptec Ultra320 SCSI Cards User’s GuideLoading the Driver at Server BootupTo automatically load the adpu320.ham at server bootup, the startup.ncf

10-5Installing the SCSI Driver for Novell NetWareUsing the Load Command Line OptionsYou can specify several command line options when the driver is lo

10-6Adaptec Ultra320 SCSI Cards User’s GuideSample Load CommandsHere is a simple load command with no option switches (if loaded from drive A):load a:

10-7Installing the SCSI Driver for Novell NetWare3 Select the removable-media device. The following drive status items appear: Mount StatusMounting ca

10-8Adaptec Ultra320 SCSI Cards User’s GuideUsing the NetWare Tape BackupIncluded with Novell NetWare is a server-based tape backup utility called sba

10-9Installing the SCSI Driver for Novell NetWareUsing a CD with NetWareNetWare 5.x and 6.xTo use a CD with NetWare 5.x and 6.x:1 Load adpu320.ham by

10-10Adaptec Ultra320 SCSI Cards User’s GuideTroubleshootingError MessagesThe error messages listed below are the messages associated with the adpu320

xiiAdaptec Ultra320 SCSI Cards User’s Guide8 Installing the SCSI Driver For Windows 2000/2003 and XP Installing the Driver When Installing Windows 8-2

10-11Installing the SCSI Driver for Novell NetWare[xxxxx085] Unable to allocate memory This indicates that there may be a problem with the amount of m

10-12Adaptec Ultra320 SCSI Cards User’s Guide[xxxxx0ac] Driver already loaded for all host bus adaptersThe driver is already loaded for all the suppor

11-111Installing the SCSI Driver for UnixWare, OpenServer, and Open UnixIn this Chapter...This chapter explains how to install the Adaptec Ultra320 SC

11-2Adaptec Ultra320 SCSI Cards User’s GuideIf you are performing a first time UnixWare/Open Unix installation, see Installing the Driver When Install

11-3Installing the SCSI Driver for UnixWare, OpenServer, and Open Unix4 If you have additional HBA disks, insert the next HBA disk, select Install Ano

11-4Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When UnixWare/Open Unix is Already InstalledTo update or install the adpu320 driver

11-5Installing the SCSI Driver for UnixWare, OpenServer, and Open UnixBack Up the Kernel If you have not already done so, back up all important files

11-6Adaptec Ultra320 SCSI Cards User’s Guide4 Type mail and press Enter. The mail messages tell you if the installation was successful.If a mail messa

11-7Installing the SCSI Driver for UnixWare, OpenServer, and Open Unix2 When the kernel has been built, type the following and press Enter after each

11-8Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Installing OpenServer To install the ad320 driver at the same time you install

xiiiContentsTroubleshooting 9-9Problems and Solutions 9-9Error Messages 9-1110 Installing the SCSI Driver for Novell NetWare Installing the Driver Whe

11-9Installing the SCSI Driver for UnixWare, OpenServer, and Open UnixUsing UnixWare/Open Unix and the Host AdapterThis section contains useful inform

11-10Adaptec Ultra320 SCSI Cards User’s Guide UnixWare/Open Unix/OpenServer supports auto-configuration. When adding multiple host adapters to an exi

11-11Installing the SCSI Driver for UnixWare, OpenServer, and Open UnixTroubleshooting Problems and SolutionsMy computer crashes or displays panic mes

11-12Adaptec Ultra320 SCSI Cards User’s GuideError Messages The error messages listed below are the messages associated with the drivers. Messages are

11-13Installing the SCSI Driver for UnixWare, OpenServer, and Open Unix[xxxxx020] Adapter or target device not responding or not connectedThe target d

11-14Adaptec Ultra320 SCSI Cards User’s Guide[xxxxx041] Command aborted[xxxxx042] Command aborted[xxxxx043] Command aborted [xxxxx044] Command aborted

11-15Installing the SCSI Driver for UnixWare, OpenServer, and Open Unix[xxxxx096] Adapter hardware initialization failure - possible resource conflict

12-112Installing the SCSI Driver for Sun SolarisIn this Chapter...This chapter explains how to install the Adaptec Ultra320 driver for Solaris 9.Insta

12-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Installing Solaris 9To install Solaris 9 with an Ultra320 SCSI Host Adapter: 1

12-3Installing the SCSI Driver for Sun Solaris6 Press F2 again to load all the identified devices. Follow Sun’s installation documentation to finish t

xivAdaptec Ultra320 SCSI Cards User’s GuideUsing Multiple Host Adapters With UnixWare/Open Unix/OpenServer 11-9Removing the Driver 11-10Troubleshootin

12-4Adaptec Ultra320 SCSI Cards User’s Guide7 Verify if the newly installed Ultra320 driver is on your system and you have the correct version by typi

12-5Installing the SCSI Driver for Sun SolarisRemoving the Driver From Solaris 9If you no longer need the driver, you can use the following procedure

12-6Adaptec Ultra320 SCSI Cards User’s GuideAdditional Notes Known/Unresolved or FYI IssuesExternal RAID Enclosure Configuration:1 Edit /kernel/drv/sg

13-113Installing the SCSI Driver for LinuxIn this Chapter...This chapter explains how to install the Adaptec Ultra320 SCSI driver for the following Li

13-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Device Drivers for Red Hat Linux To install the device drivers for Red Hat Linux 8.0, 9.0,

14-114Installing Adaptec Storage Manager–Browser EditionIn this Chapter...This chapter discusses the installation procedure for installing Adaptec Sto

14-2Adaptec Ultra320 SCSI Cards User’s GuideSupported BrowsersTo run Adaptec Storage Manager, your computer must have a Web browser supporting JavaScr

14-3Installing Adaptec Storage Manager–Browser Edition Compact—Installs only the components required on a remotely managed system. See Managed System

14-4Adaptec Ultra320 SCSI Cards User’s Guide9 When you see the Setup Information, click Next.The Setup Status window shows progress using a scroll bar

14-5Installing Adaptec Storage Manager–Browser EditionConfiguring Internet Explorer for Local ManagementWhen using the High security setting, you must

xvContentsB Windows Error Messages Error Messages B-1Driver Error Messages B-2C Using Windows Advanced Configuration Parameters Using Windows SCSI Par

14-6Adaptec Ultra320 SCSI Cards User’s GuideConfiguring Internet Explorer for Remote ManagementIf you know the IP address of the system you want to ma

14-7Installing Adaptec Storage Manager–Browser EditionInstalling Adaptec Storage Manager on LinuxNote: When performing this installation, keep in mind

14-8Adaptec Ultra320 SCSI Cards User’s Guide9 Click OK.The Shell window you used to launch the installation indicates that some daemons are being star

14-9Installing Adaptec Storage Manager–Browser Edition2 Enter the host name or IP address of the system you want to manage and the username and passwo

A-1ATroubleshooting in WindowsIn this Appendix...Most problems for Windows can be resolved by following the recommendations in the Troubleshooting Che

A-2Adaptec Ultra320 SCSI Cards User’s GuideTroubleshooting ChecklistMost problems with using the Adaptec SCSI Card results from errors in preparing an

A-3Troubleshooting in WindowsGeneral TroubleshootingThe following procedures can be used for troubleshooting in all the Windows operating systems. For

A-4Adaptec Ultra320 SCSI Cards User’s GuideWhat if I have devices that are showing up at the wrong speed (usually slower) when the BIOS scans the SCSI

A-5Troubleshooting in WindowsWhat do I do if I am having a resources conflict?Physically move the Adaptec SCSI card to another PCI slot. It may be nec

A-6Adaptec Ultra320 SCSI Cards User’s GuideCommon Error MessagesHere is what you should do if the following messages appear on the screen at bootup:“D

xviAdaptec Ultra320 SCSI Cards User’s GuideF Migrating from HostRAID to Adaptec Ultra320 SCSI Migrating With Windows 2000 F-2Installing the Adaptec Ul

B-1BWindows Error MessagesIn this Appendix...Error MessagesError messages generated by the Windows drivers can be viewed by opening the Windows Event

B-2Adaptec Ultra320 SCSI Cards User’s Guide3 Click the Words option.In the Data section of the dialog box, the entry in the second row and second colu

B-3Windows Error Messages[xxxxx021] Target device protocol errorAn unexpected event occurred during data transfer between the adapter and target devic

B-4Adaptec Ultra320 SCSI Cards User’s Guide[xxxxx089] Unable to allocate memoryThis indicates that there may be a problem with the amount of memory in

C-1CUsing Windows Advanced Configuration ParametersIn this Appendix...Advanced users may use software parameters to alter the configuration of the Win

C-2Adaptec Ultra320 SCSI Cards User’s GuideThe following is a table of supported Windows Registry Settings. Using Windows SCSI ParametersFollow the in

C-3Using Windows Advanced Configuration Parameters MaximumLogicalUnit—This can limit the scan for connected devices on the SCSI bus. Valid values are

C-4Adaptec Ultra320 SCSI Cards User’s Guide9 Select Add Value from the Edit menu. In the Value Name edit box, enter one of the valid parameter values.

C-5Using Windows Advanced Configuration ParametersTo enter driver-specific parameters:1 Select Run from the Start button.2 Type regedt32 and press Ent

D-1DCreating Driver Floppy DisksIn this Appendix...This Appendix lists the driver installation options for each operating system and instructions for

1-11IntroductionIn this Chapter...This User’s Guide provides information about using the Adaptec SCSI Card and SCSI devices, troubleshooting, SCSI ter

D-2Adaptec Ultra320 SCSI Cards User’s GuideInstallation OptionsSome operating systems only allow the use of floppy disks to supply driver files. The o

D-3Creating Driver Floppy DisksRunning Windows To create the driver disk for all operating systems:1 Insert the Adaptec Installation CD into your CD-R

D-4Adaptec Ultra320 SCSI Cards User’s Guide4 Extract the driver package by typing:dd if=/mnt/packages/FMS/OpenUnix_8/image/driver.img of=/dev/rdsk/f03

D-5Creating Driver Floppy DisksRunning Linux To create the driver disk for Red Hat or SuSE Linux:1 Insert the Adaptec Installation CD.2 At at the root

D-6Adaptec Ultra320 SCSI Cards User’s GuideIf You Do Not Have Access to a Preinstalled SystemTo create the driver disk for all operating systems:1 Set

E-1EMigrating From Adaptec Ultra320 SCSI to HostRAIDIn this Appendix...After installing the Adaptec Ultra320 SCSI drivers, you may want to enable Host

E-2Adaptec Ultra320 SCSI Cards User’s GuideMigrating With Windows 2000Installing the HostRAID DriverTo migrate the boot channel on a SCSI card from SC

E-3Migrating From Adaptec Ultra320 SCSI to HostRAID14 Click Next again. You may be prompted with this warning message:“The software you are about to i

E-4Adaptec Ultra320 SCSI Cards User’s GuideCompleting the HostRAID Driver InstallationAfter you have installed the HostRAID driver and enabled HostRAI

E-5Migrating From Adaptec Ultra320 SCSI to HostRAIDMigrating With Windows XPInstalling the HostRAID DriverTo migrate the boot channel on a SCSI card f

1-2Adaptec Ultra320 SCSI Cards User’s GuideNote: Read the Installation Guide for your Adaptec SCSI Card if you need instructions on installing the SCS

E-6Adaptec Ultra320 SCSI Cards User’s Guide13 You may be prompted with this warning message:“The software you are installing for this hardware: Adapte

E-7Migrating From Adaptec Ultra320 SCSI to HostRAID2 At the Welcome to the Found New Hardware Wizard window, select Next.3 Select Install the software

E-8Adaptec Ultra320 SCSI Cards User’s Guide7 From the Install Driver window, select the the Adaptec HostRAID U320 Driver for Windows NT 4 from the lis

E-9Migrating From Adaptec Ultra320 SCSI to HostRAID3 When the message Are you sure you want to remove this driver? appears, Click Yes and restart the

F-1FMigrating from HostRAID to Adaptec Ultra320 SCSIIn this Appendix...If after installing the HostRAID drivers, you decide to use your controller as

F-2Adaptec Ultra320 SCSI Cards User’s GuideMigrating With Windows 2000Installing the Adaptec Ultra320 SCSI DriverTo migrate the boot channel on HostRA

F-3Migrating from HostRAID to Adaptec Ultra320 SCSI14 Click Next again. You may be prompted with this warning message:“The software you are about to i

F-4Adaptec Ultra320 SCSI Cards User’s Guide8 Repeat Steps 4 through 7 if there is another array. You will also need to delete any spares.9 Once all th

F-5Migrating from HostRAID to Adaptec Ultra320 SCSI4 When the driver is copied on the hard disk drive, click Finish.5 You will be prompted to restart

F-6Adaptec Ultra320 SCSI Cards User’s Guide9 Click on the path D:\drivers\windows\win32bit or D:\drivers\windows\win64bit (where D: is the CD-ROM driv

1-3Introduction Adaptec SCSI Card 29320A SCSI Channel (SE) —has two internal connectors. SCSI Channel (Ultra320)—has one internal connector and one

F-7Migrating from HostRAID to Adaptec Ultra320 SCSI4 Select the array by scrolling to it and pressing Enter. This will display the members of that arr

F-8Adaptec Ultra320 SCSI Cards User’s Guide3 At the Please select the best match... window, keep the default drive that is highlighted and click Next.

F-9Migrating from HostRAID to Adaptec Ultra320 SCSIDisabling HostRAID SupportAfter installing the HostRAID driver, you must disable HostRAID support b

F-10Adaptec Ultra320 SCSI Cards User’s Guide13 Press Esc, save change, then exit.If you are using a dual channel card, select Channel B and repeat the

Glossary-1GlossaryAA TermA definition array Two or more disks configured to appear as a single disk to the host system.array controllerThe electronic

Glossary-2Adaptec Ultra320 SCSI Cards User’s Guidecheck pointA feature that enables you to exit the SCSISelect utility when an operation is in progres

Glossary-3GlossaryeventA notification or alert from the system indicating that a change has occurred.event logA file used to maintain information abou

Glossary-4Adaptec Ultra320 SCSI Cards User’s GuideIinitialized arrayAn array that is ready for data reads and writes.Llogical deviceA read/write resou

Glossary-5Glossaryphysical resourcesThe Adaptec Family Adapter products, channels, and SCSI devices installed in the server.pollA validation of discov

Glossary-6Adaptec Ultra320 SCSI Cards User’s GuideSSCSIStands for Small Computer System Interface. A parallel interface standard used to connect vario

iiCopyright© 2003 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in an

1-4Adaptec Ultra320 SCSI Cards User’s GuideHostRAID on Adaptec SCSI CardsHostRAID is a product that adds entry-level RAID functionality to SCSI ASICs

Glossary-7Glossarystriping, disk; striped arraySpreading data over multiple disks to enhance performance. Often referred to as RAID 0, simple data str

Index-1IndexAAdaptec customer support iiiAdaptec Storage Manager-Browser Editioncustom and compact installations 14-2defining 1-4installing on Linu

Index-2Adaptec Ultra320 SCSI Cards User’s Guideextended Interrupt 13h translation3-10FFault-tolerant redundancy 1-10HHostRAIDdefining 1-4enabling 4

Index-3Indextroubleshooting 10-10tsa.nlm 10-8using a CD-ROM 10-9OOpen Unixbooting 11-6command syntax 11-4driver installation 11-2 to 11-7kernel

Index-4Adaptec Ultra320 SCSI Cards User’s Guidegeneral guidelines 1-8listing 3-16SCSISelect 3-12, 3-16, 3-19changing device settings 3-16configurat

Index-5IndexVVerifying a build 4-13Viewing array 4-5WWide negotiation 3-6Windows 2000driver installation 5-2 to 5-3,8-2error messages 8-9install

RAdaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035 USA© 2003 Adaptec, Inc.All rights reserved. Adaptec and the Adaptec logo are trademarks o

1-5Introduction Support for transparent array (data) migration to Adaptec Intelligent RAID cards Supports Hot Swap of drives Support for Auto Rebui

1-6Adaptec Ultra320 SCSI Cards User’s GuideOperating SystemsNote: If you want to migrate between the HostRAID and Standalone SCSI drivers, see Appendi

1-7Introduction Windows XP Linux Red Hat 8.0 and 9.0 Red Hat Advanced Server 2.1 SuSE 8.1 and 8.2 SuSE Enterprise 8Note: Visit www.adaptec.com f

1-8Adaptec Ultra320 SCSI Cards User’s GuideUnderstanding SCSISCSI (pronounced “scuzzy”) stands for Small Computer Systems Interface. SCSI is an indust

1-9Introduction On both SCSI buses (channels) the Adaptec SCSI Card is preset to SCSI ID 7 and should not be changed. This gives the card the highest

1-10Adaptec Ultra320 SCSI Cards User’s Guide Termination on SE internal SCSI devices is usually controlled by manually setting a jumper or a switch o

1-11IntroductionSupported RAID Levels HostRAID includes a BIOS Configuration Utility for boosting disk performance and data protection. Adaptec SCSI C

2-12Using the Adaptec SCSI Card and SCSI DevicesIn this Chapter...This section provides useful information on using the Adaptec SCSI Card and your SCS

2-2Adaptec Ultra320 SCSI Cards User’s GuideUsing SCSI DevicesIf you connect SCSI devices (such as scanners, tape drives, zip drives, etc.) to your Ada

iiiAdaptec Customer SupportIf you have questions about installing or using your Adaptec product, check this document first—you will find answers to mo

2-3Using the Adaptec SCSI Card and SCSI DevicesUsing Ultra320/Ultra160 Hard Disk Drives For the dual-channel cards, Adaptec recommends that you conne

2-4Adaptec Ultra320 SCSI Cards User’s GuideAdaptec SCSI Card 29320AThe following is a figure of the Adaptec SCSI Card 29320A. Adaptec SCSI Card 29320A

2-5Using the Adaptec SCSI Card and SCSI DevicesWhen you install an Adaptec SCSI Card and SCSI disk drives in a computer that boots from a non-SCSI dis

2-6Adaptec Ultra320 SCSI Cards User’s GuideInstalling Multiple SCSI Cards You can install multiple SCSI cards in your computer; you are limited only

2-7Using the Adaptec SCSI Card and SCSI DevicesConnecting the LED Connector(Optional feature) Most computers have an LED disk activity light on the fr

2-8Adaptec Ultra320 SCSI Cards User’s GuideAdaptec SCSI Card 39320ATo manually terminate Channel A, place a shunt on jumper J5. To manually terminate

2-9Using the Adaptec SCSI Card and SCSI DevicesAdaptec SCSI Card 29320ALPTo manually terminate the channel on the Adaptec SCSI card 29320ALP, place a

2-10Adaptec Ultra320 SCSI Cards User’s GuideAdaptec SCSI Card 39320AThe following figure shows Ultra320/Ultra160 and Ultra2 SCSI devices connected to

2-11Using the Adaptec SCSI Card and SCSI DevicesThe following figure shows LVD SCSI devices on Channel A and non-LVD SCSI devices on Channel B.Adaptec

2-12Adaptec Ultra320 SCSI Cards User’s GuideThe following figure shows LVD SCSI (Ultra320/Ultra160 and Ultra2) devices connected to the internal and e

ivEurope Visit our Web site at www.adaptec-europe.com. German: To speak with a Technical Support Specialist, call +49 89 43 66 55 22, Monday to Frid

2-13Using the Adaptec SCSI Card and SCSI DevicesThe following example shows SCSI devices connected to the internal connector. The following example sh

2-14Adaptec Ultra320 SCSI Cards User’s GuideMaximum Cable LengthsThe total length of cabling (internal and external) on the SCSI bus cannot exceed the

3-13Configuring the Adaptec SCSI Card with SCSISelectIn this Chapter...SCSISelect, which is included with the Adaptec SCSI Card, enables you to change

3-2Adaptec Ultra320 SCSI Cards User’s GuideThe default settings are appropriate for most systems and should not be changed. Run SCSISelect if you need

3-3Configuring the Adaptec SCSI Card with SCSISelectStarting SCSISelectTo start SCSISelect:1 Turn on or restart your computer.During the startup proce

3-4Adaptec Ultra320 SCSI Cards User’s GuideExiting SCSISelectTo exit SCSISelect:1 Press Esc until a message prompts you to exit (if you changed any se

3-5Configuring the Adaptec SCSI Card with SCSISelectBoot Device Configuration Options – BBS Systems Only Select Master SCSI Controller—Enables you to

3-6Adaptec Ultra320 SCSI Cards User’s GuideSCSI Device Configuration OptionsSCSI Device Configuration options can be set individually for each connect

3-7Configuring the Adaptec SCSI Card with SCSISelect QAS—(Default:Ye s) Quick Arbitration and Selection reduces the overhead of control release on th

3-8Adaptec Ultra320 SCSI Cards User’s GuideThe following options have no effect if the SCSI card BIOS is disabled. (The SCSI card BIOS is normally ena

vLimited 5-Year Hardware Warranty1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from defects in material

3-9Configuring the Adaptec SCSI Card with SCSISelect Extended INT 13 Translation for DOS Drives > 1 GByte—(Default: Enabled) When set to Enabled,

3-10Adaptec Ultra320 SCSI Cards User’s Guide SCSI Controller INT 13 Support—(Default: Enabled) This option controls the state of the BIOS at POST tim

3-11Configuring the Adaptec SCSI Card with SCSISelect Support Removable Disks Under INT 13 as Fixed Disks—(Default: Disabled) Determines which remova

3-12Adaptec Ultra320 SCSI Cards User’s GuideChanging Configuration SettingsThe factory default settings for the Adaptec SCSI Card are correct for most

3-13Configuring the Adaptec SCSI Card with SCSISelectThe Configuration menu appears. The Configuration menu displays the current settings for the SCSI

3-14Adaptec Ultra320 SCSI Cards User’s GuideIf you select Boot Device Configuration, the Boot Device Configuration menu appears. The non-BBS version i

3-15Configuring the Adaptec SCSI Card with SCSISelectNote: Default settings are always marked with an asterisk. You can press F6 to return all setting

3-16Adaptec Ultra320 SCSI Cards User’s GuideIf you select Advanced Configuration Options, the Advanced Configuration Options menu appears. To change a

3-17Configuring the Adaptec SCSI Card with SCSISelectTo view the SCSI IDs:1 Start SCSISelect. See Starting SCSISelect on page 3-3.SCSISelect detects a

3-18Adaptec Ultra320 SCSI Cards User’s GuideVerifying or Formatting a Disk SCSISelect includes a utility that enables you to format and verify disks:

viAdaptec Software License AgreementPLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE SOFTWARE LICENSE TERMS OF ADAPTEC, INC. AND OTHE

3-19Configuring the Adaptec SCSI Card with SCSISelectTo use SCSISelect to format or verify a disk:1 Start SCSISelect. See Starting SCSISelect on page

4-14Using the SCSISelect Utility to Manage ArraysIn this Chapter...With SCSISelect, you can create and maintain RAID arrays when you enable the HostRA

4-2Adaptec Ultra320 SCSI Cards User’s GuideHostRAID supports the following RAID levels: RAID 0—Striping mode for boosting performance. RAID 1—Mirro

4-3Using the SCSISelect Utility to Manage Arrays4 From the Options menu, select Configure/View SCSI Controller Settings and press Enter. 5 From the C

4-4Adaptec Ultra320 SCSI Cards User’s Guide7 After you enable HostRAID, you can select Configure/View HostRAID on the Options menu to create and maint

4-5Using the SCSISelect Utility to Manage Arrays Dead—One drive in a RAID 0 array is in failed state or missing. Building—the drive is a target of a

4-6Adaptec Ultra320 SCSI Cards User’s Guide3 From the Main menu, press C to create a RAID array. Note: You must have at least two hard drives to creat

4-7Using the SCSISelect Utility to Manage Arrays5 From the Select RAID Member menu, press the Spacebar to select the hard drives you want to use in th

4-8Adaptec Ultra320 SCSI Cards User’s Guide4 Assign a RAID name by entering up to 15 alphabetic or numeric characters, then press Enter. The following

4-9Using the SCSISelect Utility to Manage Arrays3 After entering your options, if a partition exists on any of the selected drives, you will get a mes

vii7. Limited Warranty. Adaptec and its Licensor warrant only that the media upon which the Software is furnished will be free from defects in materia

4-10Adaptec Ultra320 SCSI Cards User’s Guide4 With RAID 10 you have the option to create a maximum of two spare drives. You can create: two spares be

4-11Using the SCSISelect Utility to Manage ArraysTo add a spare to an existing RAID 10 array, see Adding a Spare Drive on page 4-11.Deleting Arrays To

4-12Adaptec Ultra320 SCSI Cards User’s Guide2 Select a drive and press Enter. Select Yes when the following message appears:Are you Sure?Ye s /N oAfte

4-13Using the SCSISelect Utility to Manage Arrays3 If your array rebuilds successfully, the following message appears:Build/Rebuild Completed.Press An

4-14Adaptec Ultra320 SCSI Cards User’s Guide3 You will get a message asking if you want to automatically fix errors. Press Yes to AutoFix. This will e

4-15Using the SCSISelect Utility to Manage ArraysBootable ArrayTo create a bootable array:1 From the Main menu, select array, press Enter, then press

5-15Installing the HostRAID Driver for Windows 2000, 2003, and XPIn this Chapter...This chapter explains how to install the Adaptec HostRAID software

5-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Device Driver for Windows To begin driver installation, see either, Installing the Driver Fo

5-3Installing the HostRAID Driver for Windows 2000, 2003, and XPInstalling the Driver When Windows 2000 or Windows Server 2003 is Already InstalledTo

5-4Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver When Windows XP is Already InstalledTo update or install the a320raid.sys driver if W

viiiShould you have any questions concerning this Agreement, you may contact Adaptec by writing to: Adaptec, Inc.Legal Department691 South Milpitas Bo

5-5Installing the HostRAID Driver for Windows 2000, 2003, and XPChanging Boot ControllersIf you want to reconnect your bootable hard disk drive from t

6-16Installing the HostRAID Driver for Windows NT 4.0In this Chapter...This chapter explains how to install the Adaptec HostRAID software driver (a320

6-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling the Driver for Windows NT 4.0 To begin driver installation, see either Installing the Driver Whe

6-3Installing the HostRAID Driver for Windows NT 4.06 The screen displays the adapter drivers supported on the disk. Select Adaptec HostRAID U320 driv

6-4Adaptec Ultra320 SCSI Cards User’s GuideChanging Boot ControllersIf you want to reconnect your bootable hard disk drive from the SCSI controller to

6-5Installing the HostRAID Driver for Windows NT 4.0Boot Order In Windows NT 4.0 versus RAID ManagementDuring Windows NT 4.0 installation, Windows NT

7-17Installing the HostRAID Driver for LinuxIn this Chapter...This chapter explains how to install the Adaptec HostRAID driver for the following Linux

7-2Adaptec Ultra320 SCSI Cards User’s GuideInstalling Red Hat Linux Installing the Red Hat Driver in a New Linux SystemTo install the Red Hat 8.0, 9.0

7-3Installing the HostRAID Driver for Linux14 If you intend to install other third-party devices, proceed with the installation of those devices. Othe

7-4Adaptec Ultra320 SCSI Cards User’s Guide9 After you enable HostRAID, you can select Configure/View HostRAID on the Options menu to create and maint

ixContents1 Introduction Ultra320 SCSI on the Adaptec SCSI Card 1-2Device Drivers 1-3HostRAID on Adaptec SCSI Cards 1-4HostRAID Features 1-4Storage Ma

8-18Installing the SCSI Driver For Windows 2000/2003 and XP In this Chapter...This chapter explains how to install the Adaptec Ultra320 SCSI driver fo

8-2Adaptec Ultra320 SCSI Cards User’s GuideIf you are performing a first-time Windows installation, see Installing the Driver When Installing Windows

8-3Installing the SCSI Driver For Windows 2000/2003 and XP9 If you have no other controllers to add, press Enter to continue with the Windows installa

8-4Adaptec Ultra320 SCSI Cards User’s GuideNote: When booting on an IA-64 system with an EFI BIOS, be sure to select the Microsoft Windows XP 64-bit E

8-5Installing the SCSI Driver For Windows 2000/2003 and XP12 Select the driver from the Adaptec provider that best fits your adapter, and click Next.

8-6Adaptec Ultra320 SCSI Cards User’s GuideInstalling a New Host Adapter When Windows 2000/2003 Is Already InstalledTo install a new host adapter afte

8-7Installing the SCSI Driver For Windows 2000/2003 and XP8 After completing the installation, select Finish.9 You will be prompted to restart the com

8-8Adaptec Ultra320 SCSI Cards User’s Guide3 Insert the new SCSI adapter into an available PCI slot, leaving the existing SCSI card intact.4 Turn on y

8-9Installing the SCSI Driver For Windows 2000/2003 and XPTroubleshootingMost problems can be resolved by following the recommendations in Problems an

9-19Installing the SCSI Driver for Windows NT 4.0 In this Chapter...This chapter explains how to install the Adaptec Ultra320 SCSI driver adpu320.sys